Skip to main content
Stainless Steel
Market

Plate · Grade 430 / S43000

430 Stainless Steel Plate

430 stainless steel plate is a ferritic chromium grade used where moderate corrosion resistance, oxidation resistance and low thermal expansion are useful. Confirm that the ordered thickness is available as plate and state ASTM A240/A480 edition, condition, finish, dimensions and inspection.

Review technical resources
Grade: 430 / 1.4016
Product form: Plate
Order-specific data and limits stated
Replace with an approved product-form photo

Selecting 430 plate for the service

Send the service environment, finish and thickness for a 430 plate review.

430 contains chromium but no intentional molybdenum addition; compare the service environment and required magnetic behavior before selection.
Best for

Plate applications

Indoor equipment panels, appliance trim, formed covers and other mildly corrosive applications where magnetic behavior and finish are relevant.

Not recommended without review

Conditions that can exceed the grade margin

Do not assume 430 provides 304/316-level chloride resistance or weld performance. Strongly corrosive, marine or crevice service needs a project-specific alternative review.

Material identification

Grade 430

UNS S43000; EN 1.4016. Verify the ordered product standard and certificate.

430 Plate chemistry and property reference

Chemistry and physical properties are grade references. Mechanical values are ATI sheet/strip data and are not represented as plate-specific acceptance limits.

ATI 430 composition limits are shown as a grade reference. Confirm the ordered plate specification, edition and heat analysis. ATI publishes 450 MPa tensile, 205 MPa yield, 22% elongation and 89 HRB maximum for 430 sheet/strip. These values are material-screening references only; plate acceptance depends on thickness, condition and the ordered ASTM A240/A480 edition.

Chemical composition by mass

ElementMinimumMaximumUnit
Cr16.018.0wt %
SiN/A1.00wt %
MnN/A1.00wt %
NiN/A0.75wt %
CN/A0.12wt %
PN/A0.040wt %
SN/A0.030wt %
FeBalanceN/Awt %

Mechanical properties

PropertyMinimumMaximum / rangeUnitCondition / reference
Tensile strength450N/AMPaATI 430 sheet/strip; published minimum. Screening reference for a plate enquiry only.
0.2% proof / yield strength205N/AMPaATI 430 sheet/strip; published minimum. Screening reference for a plate enquiry only.
Elongation22N/A%ATI 430 sheet/strip; 22% published minimum; ATI notes 20% minimum at 1.27 mm and under. Screening reference for a plate enquiry only.
HardnessN/A89HRBATI 430 sheet/strip; published maximum. Screening reference for a plate enquiry only.

Typical physical properties

PropertyPublished valueBasis / note
Density7.70 g/cm³ATI 430 typical physical property; density
Linear thermal expansion (20–100°C)10.3 × 10⁻⁶ /°CATI 430 typical value; stated temperature range
Thermal conductivity (20–100°C)23.86 W/(m·K)ATI 430 typical value; stated temperature range
Specific heat (0–100°C)460 J/(kg·K)ATI 430 typical value; stated temperature range

Data note: These values are material-screening references. The governing product specification, ordered condition, dimensions and heat-specific certificate determine acceptance. Review the technical resources for the applicable purchasing basis.

Replace with an approved material inspection photo

How to specify 430 Plate

State thickness, width × length, finish, temper, edge, flatness and tolerances. Verify 430 plate sizes against the order basis and the chosen finish. When comparing a 430 plate supplier, require a 430 plate specification to ASTM A240, finish callout, certificate and dimensional tolerances. For an ASTM 430 plate enquiry, cite ASTM A240 and confirm finish, thickness and dimensional tolerances on the order.

Duty / itemStarting optionAdvantageLimitationAlternative / action
Appliance panel430 plate to specified finish and thicknessMagnetic ferritic grade can suit formed trimCheck finish direction and forming radiusRun a bend trial at the stated radius and grain direction
Equipment cover430 plate after cleaner and chloride reviewPlate form supports bends and coversAvoid chloride traps and wet crevicesCompare 304 where exposure or cleaning severity exceeds 430 margin
Decorative trim430 plate with approved surface finishFinish options affect appearanceColor and grain vary by lot and processApprove a lot-specific finish sample before production

Product standard: ASTM A240/A240M covers stainless plate, sheet and strip; ASTM A480/A480M supplies general flat-rolled requirements. State 430/S43000, edition, plate dimensions, condition, finish and supplements.
Finish and condition: Specify finish direction, protective film, edge quality and forming condition. Review the approved appearance sample and avoid iron contamination.

Order checks: confirm exact dimensional basis, tolerance, finish, edge/end preparation, quantity and delivery requirements before quotation.

430 Plate applications and limits

Discuss plate application; send the grade, product dimensions and service conditions.

430 stainless steel plate is a ferritic chromium stainless option for applications prioritizing magnetic response, formability and general atmospheric corrosion resistance. Specify thickness, finish, flatness, edge, temper and standard; do not treat 430 as a substitute for molybdenum-bearing grades in chloride exposure. Do not assume 430 provides 304/316-level chloride resistance or weld performance. Strongly corrosive, marine or crevice service needs a project-specific alternative review.

Appliance panel

ServiceInterior or protected exposure
Starting grade430 for mild exposure
Why it worksMagnetic ferritic grade can suit formed trim
LimitsCheck finish direction and forming radius
MaintenanceClean with non-contaminating tools

Equipment cover

ServiceMild atmospheric service
Starting gradeSpecify 430 plate condition
Why it worksPlate form supports bends and covers
LimitsAvoid chloride traps and wet crevices
MaintenanceRinse residues and keep drainage clear

Decorative trim

ServiceControlled visible surface
Starting gradeReview after forming
Why it worksFinish options affect appearance
LimitsColor and grain vary by lot and process
MaintenanceApprove finish sample before order

430 Plate risks to control

Failure modeTypical triggerControl / verification
Chloride pitting or stainingSalt, chloride-bearing moisture, deposits or stagnant crevices can exceed the corrosion margin of ferritic 430.Review chloride concentration, temperature and cleaning; avoid stagnant deposits and consider a more corrosion-resistant grade for severe exposure.
Visible finish mismatchFinish, grain direction, handling marks or protective-film expectations are not defined consistently.Specify finish and grain direction, edge condition and protective packaging; inspect sample and delivered lot against the agreed appearance criteria.
Forming cracks or surface damageTight bend radii, high strain, tooling condition or an unsuitable material condition can damage formed plate.Confirm condition, thickness and bend direction; validate tooling and bend radius with a representative forming trial.

Inspection and acceptance: Match grade, heat/lot and certificate to the order. Inspect dimensions, finish, condition and markings under the agreed sampling plan. Define measurement method, tolerance and supplementary tests before order acceptance.

430 Plate standards and designation

State S43000, ASTM editions, plate dimensions, condition, finish, tolerances, inspection and heat/lot certificate.

Standard / designationGrade designationProduct scopeProcurement caveat
ASTM A240/A240M430 / UNS S43000Plate thickness, cut size and supply condition.Ferritic S43000 properties must match the delivered form and condition.
ASTM A480/A480M430 plate general requirementsFlat-product dimensions, workmanship, finish and inspection where invoked.Define flatness, machining stock and any through-thickness examination.

430 Plate buyer questions

Is 430 stainless steel magnetic?

Yes. 430 is ferritic and normally magnetic; forming and product condition may influence response.

Can 430 replace 304 outdoors?

Not automatically. Compare chloride, moisture, pollutants, cleaning and finish; 430 has lower corrosion margin in many environments.

What plate data governs?

The ordered grade, ASTM A240 edition, thickness, condition and heat-specific certificate govern acceptance.

Does 430 plate meet a fixed hardness value?

The cited ATI plate page publishes a maximum hardness; the purchase specification and ordered product condition control.

What should a supplier quote include?

Thickness, size, finish, condition, tolerances, quantity, certificate and delivery destination.

Example: preparing a 430 plate enquiry

Include the ordered grade, product form, governing specification and required inspection evidence.

Illustrative RFQ checklist, not a customer case: 430 plate grade; ASTM A240 edition; thickness and cut size; finish/temper; tolerances; application exposure; certificate and packaging.

Service

Service

State moisture, chloride, cleaning and temperature exposure.

Plate condition

Plate condition

Define finish, temper, thickness and forming route.

Acceptance

Acceptance

Agree dimensional, visual and certificate checks.

Acceptance: Match grade, heat/lot and certificate to the order. Inspect dimensions, finish, condition and markings under the agreed sampling plan. Define measurement method, tolerance and supplementary tests before order acceptance.

Technical references for 430 Plate

ATI publishes the displayed composition and mechanical limits for 430 sheet/strip. Its technical literature describes the broader grade and notes plate availability, but the numeric table shown here remains a screening reference rather than plate-specific acceptance data.

01

ATI 430 product page

ATI page publishes sheet/strip values; use them only for grade screening and confirm plate-specific requirements and MTR.

02

ASTM A240/A240M

Confirm the current edition, plate dimensions, condition and supplementary requirements.

03

ASTM A480/A480M

State the active order edition, units and applicable supplements.

Prepare a 430 Plate quote request

State thickness, width × length, finish, temper, edge, flatness and tolerances. Verify 430 plate sizes against the order basis and the chosen finish. When comparing a 430 plate supplier, require a 430 plate specification to ASTM A240, finish callout, certificate and dimensional tolerances.

  • MaterialGrade 430; UNS S43000; EN 1.4016
  • Product formPlate
  • DimensionsState thickness, width × length, finish, temper, edge, flatness and tolerances. Verify 430 plate sizes against the order basis and the chosen finish. When comparing a 430 plate supplier, require a 430 plate specification to ASTM A240, finish callout, certificate and dimensional tolerances. For an ASTM 430 plate enquiry, cite ASTM A240 and confirm finish, thickness and dimensional tolerances on the order.
  • Standard and conditionASTM A240/A240M covers stainless plate, sheet and strip; ASTM A480/A480M supplies general flat-rolled requirements. State 430/S43000, edition, plate dimensions, condition, finish and supplements.
  • Service / fabrication430 stainless steel plate is a ferritic chromium stainless option for applications prioritizing magnetic response, formability and general atmospheric corrosion resistance. Specify thickness, finish, flatness, edge, temper and standard; do not treat 430 as a substitute for molybdenum-bearing grades in chloride exposure. Do not assume 430 provides 304/316-level chloride resistance or weld performance. Strongly corrosive, marine or crevice service needs a project-specific alternative review.
  • Inspection requirementsMatch grade, heat/lot and certificate to the order. Inspect dimensions, finish, condition and markings under the agreed sampling plan. Define measurement method, tolerance and supplementary tests before order acceptance.

Product-specific review: Attach the drawing and state specification, dimensions, condition, finish, quantity, inspection requirements and certificate.