Skip to main content
Stainless Steel
Market

Round tube; exact route and availability must be verified · Grade 310 / S31000

310 Stainless Steel Round Tube

310 Stainless Steel Round Tube requires the exact alloy identity plus a verified round tube route. State OD, wall, length, ovality, straightness, end preparation, bead condition and finished tolerances, condition, finish, inspection, certification and service before quotation.

Review technical resources
Grade: 310 / UNS S31000
Product form: Round tube; exact route and availability must be verified
Order-specific data and limits stated
Replace with an approved product-form photo

Is 310 Stainless Steel Round Tube suitable for this duty?

Share the service environment, product route, dimensions, final condition and acceptance requirements for review.

310 identifies the alloy, while round tube route, geometry, condition and service determine finished-product acceptance.
Best for

Round tube; exact route and availability must be verified applications

Furnace, thermowell, exhaust or high-temperature round-tube service after qualification where route, geometry, condition and evidence are controlled.

Not recommended without review

Conditions that can exceed the grade margin

Ordering by grade and nominal size alone or applying another product form’s data as a finished-product guarantee.

Material identification

Grade 310

UNS S31000; EN —. Verify the ordered product standard and certificate.

310 Stainless Steel Round Tube chemistry and property reference

Alloy and producer values are screening references; the verified round tube specification and heat/lot certificate govern acceptance.

310 / UNS S31000 composition identifies the alloy; heat analysis and product coverage govern. Mechanical rows are intentionally shown as em dashes because no single value applies across every round tube size, route and condition. The controlled product standard and lot certificate govern.

Chemical composition by mass

ElementMinimumMaximumUnit
C—0.25wt %
Mn—2.00wt %
Si—1.50wt %
P—0.045wt %
S—0.030wt %
Cr24.0026.00wt %
Ni19.0022.00wt %
N——wt %
Mo——wt %
FeBalance—wt %

Typical physical properties

PropertyPublished valueBasis / note
Density7.9 g/cm³Typical heat-resistant austenitic screening value; not form-specific acceptance.
Elastic modulus at 20°C200 GPaTypical annealed austenitic screening value.
Thermal conductivity at 20°C14.2 W/(m·K)Typical producer or engineering screening value.
Mean expansion, 20–100°C15.9 × 10⁻⁶/KTypical screening value; temperature interval and grade variant govern.
Heat-service basisHigh-chromium high-nickel austenitic heat-resistant familyDesign temperature, environment and ordered condition govern.

Data note: These values are material-screening references. The governing product specification, ordered condition, dimensions and heat-specific certificate determine acceptance. Review the technical resources for the applicable purchasing basis.

Replace with an approved material inspection photo

How to specify 310 Stainless Steel Round Tube

OD, wall, length, ovality, straightness, end preparation, bead condition and finished tolerances.

Duty / itemStarting optionAdvantageLimitationAlternative / action
furnace, thermowell, exhaust or high-temperature round-tube service after qualificationASTM A213/A213M, A269/A269M or A554/A554M only when S31000 and the ordered tube route are coveredMatches 310 alloy identity to a form-specific round tube route.310/310S substitution, tube/pipe confusion, heat treatment, ovality, oxidation environment and finished properties require product-specific control.State OD, wall, length, ovality, straightness, end preparation, bead condition and finished tolerances.
Dimensional and fabrication control for round tubeOD, wall, length, ovality, straightness, end preparation, bead condition and finished tolerancesConnects the supplied form to tooling, assembly and inspection.Nominal grade and size do not define finished geometry.Use an approved drawing and first-article plan.
Condition, surface and evidenceseamless or welded route as specified, heat treatment, scale removal, bead condition, ID/OD finish and packageMakes finish, handling and traceability auditable.Typical alloy data are not finished-product guarantees.State tests, marking, MTR and package.

Product standard: Approved grade-specific round tube specification is the primary route statement; supporting dimensional and general requirements do not replace verified grade coverage.
Finish and condition: Seamless or welded route as specified, heat treatment, scale removal, bead condition, ID/OD finish and package.

Order checks: confirm exact dimensional basis, tolerance, finish, edge/end preparation, quantity and delivery requirements before quotation.

310 Stainless Steel Round Tube applications and qualification

Include OD, wall, straightness, finish, and cut length.

Potential uses depend on the exact round tube route, dimensions, condition, environment, temperature and approved drawing.

furnace, thermowell, exhaust or high-temperature round-tube service after qualification

Service310 round tube for furnace, thermowell, exhaust or high-temperature round-tube service after qualification.
Starting grade310 / UNS S31000; round tube route.
Why it works310 chemistry supports round tube screening.
LimitsVerify 310 round tube dimensions, condition and code.
MaintenanceKeep 310 round tube heat and MTR records.

Fabricated assemblies using round tube

Service310 round tube fabrication.
Starting grade310 / UNS S31000; define round tube tolerances.
Why it worksControlled 310 round tube geometry supports fit-up.
LimitsMatch 310 round tube drawing, finish and tests.
MaintenanceInspect 310 round tube dimensions and lot ID.

Heat/lot-traceable 310 supply

Service310 round tube traceable supply.
Starting grade310 / UNS S31000; qualified round tube lot.
Why it works310 round tube traceability supports release.
LimitsConfirm 310 round tube availability and certification.
MaintenanceLink 310 round tube packaging and certificates.

310 Stainless Steel Round Tube route, geometry, condition and acceptance risks to control

Failure modeTypical triggerControl / verification
round tube route omittedOrder states only 310 stainless steel and a generic product nounState ASTM A213/A213M, A269/A269M or A554/A554M only when S31000 and the ordered tube route are covered.
Geometry treated as interchangeableNominal size is used without OD, wall, length, ovality, straightness, end preparation, bead condition and finished tolerancesApprove a round tube-specific drawing and tolerances.
Alloy data used as finished-product guaranteesChemistry or typical producer data replace ordered condition and lot testsUse size-, route- and condition-specific acceptance plus MTR.
Service and evidence left openFinish, inspection, service temperature, marking or package are not statedSpecify seamless or welded route as specified, heat treatment, scale removal, bead condition, ID/OD finish and package and governing service/code basis.

Inspection and acceptance: Verify S31000 heat analysis, exact round tube designation, route, dimensions, condition, required tests, marking and MTR.

310 Stainless Steel Round Tube standards and designation

UNS S31000 identifies the alloy; the controlled product specification, drawing and purchase order establish round tube acceptance.

Standard / designationGrade designationProduct scopeProcurement caveat
Approved grade-specific round tube specificationType 310 / UNS S31000 round tubeControls OD, wall, length, ovality, straightness, end preparation, bead condition and finished tolerances.Verify current edition and exact grade/form coverage before purchase.
Applicable ASTM supporting requirementsGeneral round tube requirementsSupports dimensions, finish, inspection, marking and packaging.Product specification, drawing and order prevail.
Inspection and certificate planTraceable 310 lotControls heat analysis, condition, tests, marking and MTR.Availability and delivery are quotation-specific.

310 Stainless Steel Round Tube FAQ

What grade must be stated for 310 Stainless Steel Round Tube?

State 310 / UNS S31000 and verify the exact product-standard route.

Is the marketing name enough to order this product?

No. The order also needs OD, wall, length, ovality, straightness, end preparation, bead condition and finished tolerances.

Can another product form’s mechanical data be used?

No. Finished-product acceptance must come from the ordered round tube standard, size, condition and lot tests.

What surface and condition information is needed?

State seamless or welded route as specified, heat treatment, scale removal, bead condition, ID/OD finish and package.

What should the certificate prove?

Verify heat analysis, product route, dimensions, condition, required tests, marking and heat/lot traceability.

Example 301 round order review

Ready to quote? Provide UNS S31000, exact round tube route, dimensions, condition, quantity and certificate basis.

Illustrative enquiry: 310 Stainless Steel Round Tube; state OD, wall, length, ovality, straightness, end preparation, bead condition and finished tolerances, condition, finish, tests, quantity and MTR.

Define

Define the round tube duty

State service, loads, temperature, environment, downstream process and governing code.

Specify

Specify route and geometry

State ASTM A213/A213M, A269/A269M or A554/A554M only when S31000 and the ordered tube route are covered; then define OD, wall, length, ovality, straightness, end preparation, bead condition and finished tolerances.

Verify

Verify the supplied lot

Check heat identity, dimensions, condition, surface, tests, markings and MTR before release.

Acceptance: Verify S31000 heat analysis, exact round tube designation, route, dimensions, condition, required tests, marking and MTR.

Technical references for 310 Stainless Steel Round Tube

Primary standards and producer data support screening; the controlled order and heat/lot evidence determine acceptance.

01

Outokumpu Therma 310 producer-range data

Typical data are not finished-product guarantees.

02

Approved grade-specific round tube specification

Verify controlled-edition coverage before ordering.

03

Applicable ASTM supporting requirements

Product specification, drawing, code and MTR remain controlling.

Prepare a complete round tube quote request

Separate alloy identity from product route, geometry, condition, service and evidence.

  • MaterialGrade 310; UNS S31000; EN —
  • Product formRound tube; exact route and availability must be verified
  • DimensionsOD, wall, length, ovality, straightness, end preparation, bead condition and finished tolerances.
  • Standard and conditionApproved grade-specific round tube specification is the primary route statement; supporting dimensional and general requirements do not replace verified grade coverage.
  • Service / fabricationPotential uses depend on the exact round tube route, dimensions, condition, environment, temperature and approved drawing.
  • Inspection requirementsVerify S31000 heat analysis, exact round tube designation, route, dimensions, condition, required tests, marking and MTR.

Product-specific review: State UNS S31000, the approved product route, OD, wall, length, ovality, straightness, end preparation, bead condition and finished tolerances, condition, required tests, quantity and MTR.